Before you start: know which part goes where
The No3 set has two parts that behave differently: the clamps themselves and the remote. The clamps are made from food-grade silicone with an ABS body, and each clamp measures 46mm × 46mm × 16.8mm and weighs 22g. The remote is ABS, 36mm × 36mm × 18mm, and weighs 40g. Only the clamps are IPX6 water-resistant; the remote is not waterproof, so keep it away from water and wipe it with a damp cloth when needed. Charging is also separate: the clamps use magnetic fast charging, while the remote charges by USB-C. Both arrive with their own charging needs, so charge each part before a session.
Pairing the No3 smart nipple clamp with its remote
The supplied information confirms Bluetooth remote control at up to 15 meters, but does not include a step-by-step pairing sequence. Use the following as a sensible starting point, and check the manual that comes with your set for the exact button combination.
- Charge both parts first: Connect the clamps to their magnetic charger and the remote to a USB-C cable. A full charge on both avoids a mid-session stop.
- Power on the clamps: Turn on the clamps using the control on the clamp body. The supplied information does not specify the exact button or light pattern, so refer to your manual.
- Power on the remote: Switch on the remote and bring it close to the clamps for the first pairing.
- Put the remote into pairing mode: Follow the manual's pairing instruction. If no clamps appear, turn both parts off and repeat the sequence.
- Test the connection: Once paired, press a vibration button on the remote and confirm the clamps respond before you put them on.
Choosing a vibration pattern and clamp strength
The No3 offers five vibration modes—low, medium, high, periodic waveform, and intermittent pulse—and four clamp-strength levels. Start with the lowest strength and the lowest vibration mode. The clamp has three texture options: granular (dense and intense), surrounding cavity (gentle wrap), and ripple (long, soothing). You can adjust clamp strength independently of vibration, so try a gentle clamp with a low pattern first, then increase one variable at a time. The motor is rated at 12,000 rpm, and noise is listed at ≤45 dB in silent mode, which is close to ambient room sound.
How to wear the clamps comfortably and discreetly
The clamps are designed to be lightweight and low-profile: each weighs 22g, and the silicone contact points are soft. The set comes in White or Pink, and the clamps are shaped to sit like a small patch under clothing. The supplied information does not include a recommended wear duration, so use your own comfort as the guide and remove them if you feel discomfort.
- Position the clamp: Place the clamp so the silicone contact points sit comfortably. The 46mm × 46mm face is designed to stay in place without pressing hard.
- Set clamp strength: Use the lowest of the four strength levels first. Increase only if you want more pressure.
- Check the fit under clothing: The clamps are meant to be worn discreetly. Try them under a loose top first to confirm they stay put and feel comfortable.
- Keep the remote handy: The remote works up to 15 meters away, so you can adjust settings without reaching for the clamps.
No3 specs that affect setup and wear
- No3 Wireless Smart Nipple Clamp Massager: Clamps: 46mm × 46mm × 16.8mm, 22g each; remote: 36mm × 36mm × 18mm, 40g. These dimensions help you judge how discreet the clamps are and how the remote feels in hand.

No3 Wireless Smart Nipple Clamp Massager - No3 Wireless Smart Nipple Clamp Massager: Clamps are IPX6 water-resistant; the remote is not waterproof. You can rinse the clamps, but the remote must be kept dry and wiped clean.
- No3 Wireless Smart Nipple Clamp Massager: Clamps use magnetic fast charging; remote uses USB-C. Plan to charge each part separately before use.
- No3 Wireless Smart Nipple Clamp Massager: Five vibration modes and four clamp-strength levels. You can fine-tune sensation without changing the physical fit.
- No3 Wireless Smart Nipple Clamp Massager: Noise ≤45 dB in silent mode. This is close to ambient sound, so discreet wear is more practical.
Cleaning and storage after wear
Clean the clamps with warm water and mild soap, since they are IPX6 water-resistant. Wipe the remote with a damp cloth—do not rinse or submerge it. Dry both parts fully before storing. Keep the set in a cool, dry place, and store the clamps away from sharp objects to protect the silicone. The supplied information does not specify a cleaning solution beyond water and mild soap, so avoid harsh chemicals.

